[cle-release-team] Testing of the LDAP Return Limit

[Mike Jennings]

Ok, this is obviously the first time I have done this, but how do I mark 
the jira https://jira.sakaiproject.org/browse/SAK-21105 as verified?

Mike

==============================================================================
Mike Jennings
Teaching and Learning Developer
University of North Carolina at Chapel Hill

Office: (919) 843-5013
Cell: (919) 698-3746
E-mail: mike_jennings at unc.edu

On 7/25/2012 5:43 PM, Aaron Zeckoski wrote:
> Thanks Mike!
> -AZ
>
>
> On Wed, Jul 25, 2012 at 5:39 PM, Mike Jennings <mike_jennings at unc.edu> wrote:
>> Aaron/Sam,
>>
>> Thanks for the info.  I will have this tested and verified before the
>> call tomorrow am.
>>
>> Mike
>>
>> ==============================================================================
>> Mike Jennings
>> Teaching and Learning Developer
>> University of North Carolina at Chapel Hill
>>
>> Office: (919) 843-5013
>> Cell: (919) 698-3746
>> E-mail: mike_jennings at unc.edu
>>
>> On 7/25/2012 5:18 PM, Aaron Zeckoski wrote:
>>> Oh right..... (head desk)... listen to Sam and ignore me. Always a good policy.
>>> :-)
>>> -AZ
>>>
>>>
>>> On Wed, Jul 25, 2012 at 5:15 PM, Sam Ottenhoff <ottenhoff at longsight.com> wrote:
>>>> First, enable debugging on edu.amc
>>>> (log.config.count=1;log.config.1=DEBUG.edu.amc).
>>>>
>>>> Then, don't use User Membership (that does wildcard searches), use Site Info
>>>> instead.  Add 20 LDAP users to your site.  Observe the LDAP queries in the
>>>> logs.  It should print out the actual filter being used to construct the
>>>> searches.
>>>>
>>>> Note that there is a 5 minute cache by default.  You can always clear your
>>>> defaults by going to Administration Workspace -> Memory -> Reset all.
>>>>
>>>> --Sam
>>>>
>>>> On Wed, Jul 25, 2012 at 5:10 PM, Aaron Zeckoski <azeckoski at unicon.net>
>>>> wrote:
>>>>>
>>>>> Sounds like a good start. In general, the easiest place to test is
>>>>> probably the user memberships tool. That way you can do searches which
>>>>> you know will return a certain number of results (like all users with
>>>>> "aa" in their name or something).
>>>>>
>>>>> Then you probably will need to actually stick a debug marker and watch
>>>>> the execution to make sure the data is coming through the function in
>>>>> the JLDAP provider correctly. I'm not sure what the method is off the
>>>>> top of my head but it will be the one that was modified most heavily
>>>>> in the patch. If you can't find it then let me know and I can dig it
>>>>> up.
>>>>>
>>>>> :-)
>>>>> -AZ
>>>>>
>>>>>
>>>>> On Wed, Jul 25, 2012 at 4:58 PM, Mike Jennings <mike_jennings at unc.edu>
>>>>> wrote:
>>>>>> Aaron,
>>>>>>
>>>>>> I have setup the trunk version of sakai to point to UNC's LDAP and I can
>>>>>> successfully authenticate using my ldap credentials.
>>>>>>
>>>>>> I am trying to figure out where you want me to do the search so that I
>>>>>> can
>>>>>> test this out for you and prove that only 10 results will be returned if
>>>>>> I
>>>>>> set the max returned to be 10...
>>>>>>
>>>>>> This is for https://jira.sakaiproject.org/browse/SAK-21105
>>>>>>
>>>>>> Mike
>>>>>> --
>>>>>>
>>>>>> ==============================================================================
>>>>>> Mike Jennings
>>>>>> Teaching and Learning Developer
>>>>>> University of North Carolina at Chapel Hill
>>>>>>
>>>>>> Office: (919) 843-5013
>>>>>> Cell: (919) 698-3746
>>>>>> E-mail: mike_jennings at unc.edu
>>>>>
>>>>>
>>>>>
>>>>> --
>>>>> Aaron Zeckoski - Software Architect - http://tinyurl.com/azprofile
>>>>> _______________________________________________
>>>>> cle-release-team mailing list
>>>>> cle-release-team at collab.sakaiproject.org
>>>>> http://collab.sakaiproject.org/mailman/listinfo/cle-release-team
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> cle-release-team mailing list
>>>> cle-release-team at collab.sakaiproject.org
>>>> http://collab.sakaiproject.org/mailman/listinfo/cle-release-team
>>>>
>>>
>>>
>>>
>> _______________________________________________
>> cle-release-team mailing list
>> cle-release-team at collab.sakaiproject.org
>> http://collab.sakaiproject.org/mailman/listinfo/cle-release-team
>
>
>