[cle-release-team] Testing of the LDAP Return Limit

[Aaron Zeckoski]

Thanks Mike!
-AZ


On Wed, Jul 25, 2012 at 5:39 PM, Mike Jennings <mike_jennings at unc.edu> wrote:
> Aaron/Sam,
>
> Thanks for the info.  I will have this tested and verified before the
> call tomorrow am.
>
> Mike
>
> ==============================================================================
> Mike Jennings
> Teaching and Learning Developer
> University of North Carolina at Chapel Hill
>
> Office: (919) 843-5013
> Cell: (919) 698-3746
> E-mail: mike_jennings at unc.edu
>
> On 7/25/2012 5:18 PM, Aaron Zeckoski wrote:
>> Oh right..... (head desk)... listen to Sam and ignore me. Always a good policy.
>> :-)
>> -AZ
>>
>>
>> On Wed, Jul 25, 2012 at 5:15 PM, Sam Ottenhoff <ottenhoff at longsight.com> wrote:
>>> First, enable debugging on edu.amc
>>> (log.config.count=1;log.config.1=DEBUG.edu.amc).
>>>
>>> Then, don't use User Membership (that does wildcard searches), use Site Info
>>> instead.  Add 20 LDAP users to your site.  Observe the LDAP queries in the
>>> logs.  It should print out the actual filter being used to construct the
>>> searches.
>>>
>>> Note that there is a 5 minute cache by default.  You can always clear your
>>> defaults by going to Administration Workspace -> Memory -> Reset all.
>>>
>>> --Sam
>>>
>>> On Wed, Jul 25, 2012 at 5:10 PM, Aaron Zeckoski <azeckoski at unicon.net>
>>> wrote:
>>>>
>>>> Sounds like a good start. In general, the easiest place to test is
>>>> probably the user memberships tool. That way you can do searches which
>>>> you know will return a certain number of results (like all users with
>>>> "aa" in their name or something).
>>>>
>>>> Then you probably will need to actually stick a debug marker and watch
>>>> the execution to make sure the data is coming through the function in
>>>> the JLDAP provider correctly. I'm not sure what the method is off the
>>>> top of my head but it will be the one that was modified most heavily
>>>> in the patch. If you can't find it then let me know and I can dig it
>>>> up.
>>>>
>>>> :-)
>>>> -AZ
>>>>
>>>>
>>>> On Wed, Jul 25, 2012 at 4:58 PM, Mike Jennings <mike_jennings at unc.edu>
>>>> wrote:
>>>>> Aaron,
>>>>>
>>>>> I have setup the trunk version of sakai to point to UNC's LDAP and I can
>>>>> successfully authenticate using my ldap credentials.
>>>>>
>>>>> I am trying to figure out where you want me to do the search so that I
>>>>> can
>>>>> test this out for you and prove that only 10 results will be returned if
>>>>> I
>>>>> set the max returned to be 10...
>>>>>
>>>>> This is for https://jira.sakaiproject.org/browse/SAK-21105
>>>>>
>>>>> Mike
>>>>> --
>>>>>
>>>>> ==============================================================================
>>>>> Mike Jennings
>>>>> Teaching and Learning Developer
>>>>> University of North Carolina at Chapel Hill
>>>>>
>>>>> Office: (919) 843-5013
>>>>> Cell: (919) 698-3746
>>>>> E-mail: mike_jennings at unc.edu
>>>>
>>>>
>>>>
>>>> --
>>>> Aaron Zeckoski - Software Architect - http://tinyurl.com/azprofile
>>>> _______________________________________________
>>>> cle-release-team mailing list
>>>> cle-release-team at collab.sakaiproject.org
>>>> http://collab.sakaiproject.org/mailman/listinfo/cle-release-team
>>>
>>>
>>>
>>> _______________________________________________
>>> cle-release-team mailing list
>>> cle-release-team at collab.sakaiproject.org
>>> http://collab.sakaiproject.org/mailman/listinfo/cle-release-team
>>>
>>
>>
>>
> _______________________________________________
> cle-release-team mailing list
> cle-release-team at collab.sakaiproject.org
> http://collab.sakaiproject.org/mailman/listinfo/cle-release-team



-- 
Aaron Zeckoski - Software Architect - http://tinyurl.com/azprofile